SOLVER 4777 SUPERGLOSS ACCENT BASE
Chemwatch Independent Material Safety Data Sheet
Issue Date: 6-Jul-2008
C9317EC
CHEMWATCH 39324
Version No:4
SOLVER 4777 SUPERGLOSS ACCENT BASE
PAINT
■ The use of a quantity of material in an unventilated or confined space may result in increased exposure and an irritating atmosphere developing. Before starting consider control of exposure by mechanical ventilation.
Used according to manufacturer's directions.
Company: Solver Paints Pty Ltd Address: 560 Churchill Road Kilburn SA, 5084 Australia Telephone: +61 8 8368 1200 Emergency Tel: 1800 039 008 (24 hours) Emergency Tel: +61 3 9573 3112 Fax: +61 8 8368 1222
HAZARDOUS SUBSTANCE. DANGEROUS GOODS. According to NOHSC Criteria, and ADG Code.
S5
Risk Codes Risk Phrases R11 ■ Highly flammable. R20/21/22 ■ Harmful by inhalation, in contact with skin and if swallowed. R36/38 ■ Irritating to eyes and skin. R52/53 ■ Harmful to aquatic organisms, may cause long- term adverse effects in the aquatic environment. R63(3) ■ Possible risk of harm to the unborn child. R65 ■ HARMFUL- May cause lung damage if swallowed. R67 ■ Vapours may cause drowsiness and dizziness.
Safety Codes Safety Phrases S36 ■ Wear suitable protective clothing. S51 ■ Use only in well ventilated areas. S401 ■ To clean the floor and all objects contaminated by this material use water and detergent. S13 ■ Keep away from food drink and animal feeding stuffs. S46 ■ If swallowed IMMEDIATELY contact Doctor or Poisons Information Centre. (show this container or label). S60 ■ This material and its container must be disposed of as hazardous waste.
| NAME | CAS RN | % |
| alkyd resin solution | Various | >60 |
| contains | ||
| xylene | 1330-20-7 | 10-30 |
| aliphatic aromatic hydrocarbon | Not avail. | 10-30 |
| mineral turpentine | Not avail. | 1-10 |
| titanium dioxide | 13463-67-7 | 1-10 |
| additives non regulated as | <1.0 | |
| dispersant anti skinning agent driers | ||
| NOTE: Manufacturer has supplied full ingredient | ||
| information to allow CHEMWATCH assessment. | ||
| Lead content on non volatile | 0.00 |
· If swallowed do NOT induce vomiting.
· If vomiting occurs, lean patient forward or place on left side (head-down position, if possible) to maintain open airway and prevent aspiration.
· Observe the patient carefully.
· Never give liquid to a person showing signs of being sleepy or with reduced awareness; i.e. becoming unconscious.
· Avoid giving milk or oils.
· Avoid giving alcohol.
· If spontaneous vomiting appears imminent or occurs, hold patient's head down, lower than their hips to help avoid possible aspiration of vomitus.
■ If this product comes in contact with the eyes:
· Wash out immediately with fresh running water.
· Ensure complete irrigation of the eye by keeping eyelids apart and away from eye and moving the eyelids by occasionally lifting the upper and lower lids.
· Seek medical attention without delay; if pain persists or recurs seek medical attention.
· Removal of contact lenses after an eye injury should only be undertaken by skilled personnel.
■ If skin contact occurs:
· Immediately remove all contaminated clothing, including footwear.
· Flush skin and hair with running water (and soap if available).
· Seek medical attention in event of irritation.
· If fumes or combustion products are inhaled remove from contaminated area.
· Lay patient down. Keep warm and rested.
· Prostheses such as false teeth, which may block airway, should be removed, where possible, prior to initiating first aid procedures.
· Apply artificial respiration if not breathing, preferably with a demand valve resuscitator, bag-valve mask device, or pocket mask as trained. Perform CPR if necessary.
■ Any material aspirated during vomiting may produce lung injury. Therefore emesis should not be induced mechanically or pharmacologically. For acute or short term repeated exposures to xylene: · Gastro- intestinal absorption is significant with ingestions. For ingestions exceeding 1- 2 ml (xylene)/kg, intubation and lavage with cuffed endotracheal tube is recommended. The use of charcoal and cathartics is equivocal. · Pulmonary absorption is rapid with about 60- 65% retained at rest. · Primary threat to life from ingestion and/or inhalation, is respiratory failure. · Patients should be quickly evaluated for signs of respiratory distress (e.g. cyanosis, tachypnoea, intercostal retraction, obtundation) and given oxygen. Patients with inadequate tidal volumes or poor arterial blood gases (pO2 < 50 mm Hg or pCO2 > 50 mm Hg) should be intubated.
· Foam. · Dry chemical powder. · BCF (where regulations permit). · Carbon dioxide.
· Alert Fire Brigade and tell them location and nature of hazard. · May be violently or explosively reactive. · Wear breathing apparatus plus protective gloves. · Prevent, by any means available, spillage from entering drains or water course. When any large container (including road and rail tankers) is involved in a fire, consider evacuation by 500 metres in all directions.
· Liquid and vapour are highly flammable. · Severe fire hazard when exposed to heat, flame and/or oxidisers. · Vapour may travel a considerable distance to source of ignition. · Heating may cause expansion or decomposition leading to violent rupture of containers. Combustion products include: carbon dioxide (CO2), other pyrolysis products typical of burning organic material. Contains low boiling substance: Closed containers may rupture due to pressure buildup under fire conditions. May emit clouds of acrid smoke.
· Avoid contamination with oxidising agents i.e. nitrates, oxidising acids, chlorine bleaches, pool chlorine etc. as ignition may result.
•3YE
| Glasses: | Gloves: | Respirator: |
| Chemical goggles. | PVC chemical resistant type. | Type A-P Filter of sufficient capacity |
· Remove all ignition sources. · Clean up all spills immediately. · Avoid breathing vapours and contact with skin and eyes. · Control personal contact by using protective equipment.
· Clear area of personnel and move upwind. · Alert Fire Brigade and tell them location and nature of hazard. · May be violently or explosively reactive. · Wear breathing apparatus plus protective gloves.
Personal Protective Equipment advice is contained in Section 8 of the MSDS.
· Containers, even those that have been emptied, may contain explosive vapours.
· Do NOT cut, drill, grind, weld or perform similar operations on or near containers.
· DO NOT allow clothing wet with material to stay in contact with skin.
· Electrostatic discharge may be generated during pumping - this may result in fire.
· Ensure electrical continuity by bonding and grounding (earthing) all equipment.
· Restrict line velocity during pumping in order to avoid generation of electrostatic discharge (<=1 m/sec until fill pipe submerged to twice its diameter, then <= 7 m/sec).
· Avoid splash filling.
· Avoid all personal contact, including inhalation.
· Wear protective clothing when risk of exposure occurs.
· Use in a well-ventilated area.
· Prevent concentration in hollows and sumps.
· Packing as supplied by manufacturer.
· Plastic containers may only be used if approved for flammable liquid.
· Check that containers are clearly labelled and free from leaks.
· For low viscosity materials (i) : Drums and jerry cans must be of the non-removable head type. (ii) : Where a can is to be used as an inner package, the can must have a screwed enclosure.
· For materials with a viscosity of at least 2680 cSt. (23 deg. C)
· For manufactured product having a viscosity of at least 250 cSt. (23 deg. C)
· Manufactured product that requires stirring before use and having a viscosity of at least 20 cSt (25 deg. C).
· Avoid reaction with oxidising agents.
· Store in original containers in approved flame-proof area.
· No smoking, naked lights, heat or ignition sources.
· DO NOT store in pits, depressions, basements or areas where vapours may be trapped.
· Keep containers securely sealed.
| Source | Material | TWA ppm | TWA mg/m³ | STEL ppm | STEL mg/m³ | Notes |
| ___________ | ___________ | _______ | _______ | _______ | _______ | _______ |
| Australia Exposure Standards | xylene (Xylene (o-, m-, p- isomers)) | 80 | 350 | 150 | 655 | |
| Australia Exposure Standards | mineral turpentine (White spirits) | 790 | (see Chapter 16) | |||
| Australia Exposure Standards | mineral turpentine (Petrol (gasoline)) | 900 | (see Chapter 16) | |||
| Australia Exposure Standards | titanium dioxide (Titanium dioxide (a)) | 10 | (see Chapter 14) |
Type A- P Filter of sufficient capacity
· Safety glasses with side shields. · Chemical goggles. · Contact lenses may pose a special hazard; soft contact lenses may absorb and concentrate irritants. A written policy document, describing the wearing of lens or restrictions on use, should be created for each workplace or task. This should include a review of lens absorption and adsorption for the class of chemicals in use and an account of injury experience. Medical and first- aid personnel should be trained in their removal and suitable equipment should be readily available. In the event of chemical exposure, begin eye irrigation immediately and remove contact lens as soon as practicable. Lens should be removed at the first signs of eye redness or irritation - lens should be removed in a clean environment only after workers have washed hands thoroughly. [CDC NIOSH Current Intelligence Bulletin 59].
· Wear chemical protective gloves, eg. PVC. · Wear safety footwear or safety gumboots, eg. Rubber. Suitability and durability of glove type is dependent on usage. Important factors in the selection of gloves include: such as: · frequency and duration of contact, · chemical resistance of glove material, · glove thickness and · dexterity.
· Overalls. · PVC Apron. · PVC protective suit may be required if exposure severe. · Eyewash unit.
■ CARE: Use of a quantity of this material in confined space or poorly ventilated area, where rapid build up of concentrated atmosphere may occur, could require increased ventilation and/or protective gear. For flammable liquids and flammable gases, local exhaust ventilation or a process enclosure ventilation system may be required. Ventilation equipment should be explosion- resistant. Air contaminants generated in the workplace possess varying " escape" velocities which, in turn, determine the " capture velocities" of fresh circulating air required to effectively remove the contaminant.
| Type of Contaminant: | Air Speed: |
| solvent, vapours, degreasing etc., evaporating from tank (in still air). | 0.25- 0.5 m/s (50-100 f/min.) |
| aerosols, fumes from pouring operations, intermittent container filling, low speed conveyer transfers, welding, spray drift, plating acid fumes, pickling (released at low velocity into zone of active generation) | 0.5- 1 m/s (100-200 f/min.) |
| direct spray, spray painting in shallow booths, drum filling, conveyer loading, crusher dusts, gas discharge (active generation into zone of rapid air motion) | 1- 2.5 m/s (200-500 f/min.) |
White highly flammable liquid; does not mix with water. Strong solvent smell. Mixes with organic solvents.
Liquid.
Does not mix with water.
Floats on water.
| State | Liquid | Molecular Weight | Not applicable. |
| Melting Range (ºC) | Not available. | Viscosity | Not Available |
| Boiling Range (ºC) | Not available. | Solubility in water (g/L) | Immiscible |
| Flash Point (ºC) | -1 approx | pH (1% solution) | Not Applicable |
| Decomposition Temp (ºC) | Not Available | pH (as supplied) | Not applicable |
| Autoignition Temp (ºC) | Not available. | Vapour Pressure (kPa) | Not available. |
| Upper Explosive Limit (%) | Not Available | Specific Gravity (water=1) | 0.97 |
| Lower Explosive Limit (%) | Not Available | Relative Vapour Density (air=1) | > 2 |
| Volatile Component (%vol) | 50 approx. | Evaporation Rate | Not Available |
| xylene | |
| ■ log Kow (Prager 1995): | 3.12- 3.20 |
· Presence of incompatible materials.
· Product is considered stable.
· Hazardous polymerisation will not occur.
For incompatible materials - refer to Section 7 - Handling and Storage.
| ACUTE HEALTH EFFECTS | CHRONIC HEALTH EFFECTS |
| ■ HARMFUL-May cause lung damage if swallowed. | ■ Possible risk of harm to the unborn child. |
| ■ Harmful by inhalation, in contact with skin and if swallowed. | |
| ■ Irritating to eyes and skin. | |
| ■ Vapours may cause dizziness or suffocation. | |
| ■ Vapours may cause drowsiness and dizziness. |
MINERAL TURPENTINE: TITANIUM DIOXIDE: XYLENE: ■ unless otherwise specified data extracted from RTECS - Register of Toxic Effects of Chemical Substances. MINERAL TURPENTINE: XYLENE: ■ The material may cause skin irritation after prolonged or repeated exposure and may produce a contact dermatitis (nonallergic). This form of dermatitis is often characterised by skin redness (erythema) and swelling the epidermis. ■ The material may produce severe irritation to the eye causing pronounced inflammation. Repeated or prolonged exposure to irritants may produce conjunctivitis. ■ unless otherwise specified data extracted from RTECS - Register of Toxic Effects of Chemical Substances.
| TOXICITY | IRRITATION |
| Oral (human) LDLo: 50 mg/kg | Skin (rabbit):500 mg/24h Moderate |
| Oral (rat) LD50: 4300 mg/kg | Eye (human): 200 ppm Irritant |
| Inhalation (human) TCLo: 200 ppm | Eye (rabbit): 87 mg Mild |
| Inhalation (man) LCLo: 10000 ppm/6h | Eye (rabbit): 5 mg/24h SEVERE |
| Inhalation (rat) LC50: 5000 ppm/4h | |
| Oral (Human) LD: 50 mg/kg | |
| Inhalation (Human) TCLo: 200 ppm/4h | |
| Intraperitoneal (Rat) LD50: 2459 mg/kg | |
| Subcutaneous (Rat) LD50: 1700 mg/kg | |
| Oral (Mouse) LD50: 2119 mg/kg | |
| Intraperitoneal (Mouse) LD50: 1548 mg/kg | |
| Intravenous (Rabbit) LD: 129 mg/kg | |
| Inhalation (Guinea) pig: LC 450 ppm/4h |
| TOXICITY | IRRITATION |
| Oral (Rat) LD50: >20000 mg/kg * | Skin (human): 0.3 mg /3D (int)-Mild * |
| Oral (Mouse) LD50: >10000 mg/kg * |
| Xylenes | International Agency for Research on Cancer (IARC) - Agents Reviewed by the IARC Monographs | Group | 3 |
| Titanium dioxide | International Agency for Research on Cancer (IARC) - Agents Reviewed by the IARC Monographs | Group | 2B |
| xylene | ILO Chemicals in the electronics industry that have toxic effects on reproduction | Reduced fertility or sterility |
Harmful to aquatic organisms, may cause long- term adverse effects in the aquatic environment. This material and its container must be disposed of as hazardous waste.
| Ingredient | Persistence: Water/Soil | Persistence: Air | Bioaccumulation | Mobility |
| xylene | LOW | LOW | LOW | |
| titanium dioxide | HIGH | LOW | HIGH |
· Containers may still present a chemical hazard/ danger when empty.
· Return to supplier for reuse/ recycling if possible.
Otherwise:
· If container can not be cleaned sufficiently well to ensure that residuals do not remain or if the container cannot be used to store the same product, then puncture containers, to prevent re-use, and bury at an authorised landfill.
· Where possible retain label warnings and MSDS and observe all notices pertaining to the product.
· DO NOT allow wash water from cleaning or process equipment to enter drains.
· It may be necessary to collect all wash water for treatment before disposal.
· In all cases disposal to sewer may be subject to local laws and regulations and these should be considered first.
· Where in doubt contact the responsible authority.
· Recycle wherever possible.
· Consult manufacturer for recycling options or consult local or regional waste management authority for disposal if no suitable treatment or disposal facility can be identified.
· Dispose of by: burial in a land-fill specifically licenced to accept chemical and / or pharmaceutical wastes or Incineration in a licenced apparatus (after admixture with suitable combustible material).
· Decontaminate empty containers. Observe all label safeguards until containers are cleaned and destroyed.
Labels Required: FLAMMABLE LIQUID
●3YE (ADG7)
| Class or division: | 3 | Subsidiary risk: | None |
| UN No.: | 1263 | UN packing group: | II |
| Special provisions: | 163 | Packing Instructions: | None |
| Limited quantities: | 5 L | Portable tanks and bulk containers - Instructions: | T4 |
| Portable tanks and bulk containers - Special provisions: | TP1; TP8; TP28 | Packagings and IBCs - Packing instruction: | P001; IBC02 |
| Packagings and IBCs - Special packing provisions: | PP1 |
| Class or division: | 3 | Subsidiary risk: | None |
| UN No.: | 1263 | UN packing group: | II |
| ICAO/IATA Class: | 3 | ICAO/IATA Subrisk: | None |
| UN/ID Number: | 1263 | Packing Group: | II |
| Special provisions: | A3 | ||
| IMDG Class: | 3 | IMDG Subrisk: | None |
| UN Number: | 1263 | Packing Group: | II |
| EMS Number: | F-E , S-E | Special provisions: | 163 |
| Limited Quantities: | 5 L |
S5
Regulations for ingredients
"Australia High Volume Industrial Chemical List (HVICL)","Australia Inventory of Chemical Substances (AICS)","International Council of Chemical Associations (ICCA) - High Production Volume List","OECD Representative List of High Production Volume (HPV) Chemicals"
"Australia Exposure Standards","Australia High Volume Industrial Chemical List (HVICL)","Australia Inventory of Chemical Substances (AICS)","Australia Therapeutic Goods Administration (TGA) Substances that may be used as active ingredients in Listed medicines","Australia Therapeutic Goods Administration (TGA) Sunscreening agents permitted as active ingredients in listed products","CODEX General Standard for Food Additives (GSFA) - Additives Permitted for Use in Food in General, Unless Otherwise Specified, in Accordance with GMP","GESAMP/EHS Composite List - GESAMP Hazard Profiles","IMO IBC Code Chapter 17: Summary of minimum requirements","International Agency for Research on Cancer (IARC) - Agents Reviewed by the IARC Monographs","OECD Representative List of High Production Volume (HPV) Chemicals"
No data for alkyd resin solution (CAS: , Various)
No data for aliphatic aromatic hydrocarbon (CAS: , Not avail)
No data for mineral turpentine (CAS: , Not avail)
| Ingredient Name | CAS |
| titanium dioxide | 13463-67-7, 1317-70-0, 1317-80-2, 12188-41-9, 1309-63-3, 100292-32-8, 101239-53-6, 116788-85-3, 12000-59-8, 12701-76-7, 12767-65-6, 12789-63-8, 1344-29-2, 185323-71-1, 185828-91-5, 188357-76-8, 188357-79-1, 195740-11-5, 221548-98-7, 224963-00-2, 246178-32-5, 252962-41-7, 37230-92-5, 37230-94-7, 37230-95-8, 37230-96-9, 39320-58-6, 39360-64-0, 39379-02-7, 416845-43-7, 494848-07-6, 494848-23-6, 494851-77-3, 494851-98-8, 55068-84-3, 55068-85-4, 552316-51-5, 62338-64-1, 767341-00-4, 97929-50-5, 98084-96-9 |
■ Classification of the preparation and its individual components has drawn on official and authoritative sources as well as independent review by the Chemwatch Classification committee using available literature references.
A list of reference resources used to assist the committee may be found at:
www.chemwatch.net/references.
■ The (M)SDS is a Hazard Communication tool and should be used to assist in the Risk Assessment. Many factors determine whether the reported Hazards are Risks in the workplace or other settings.
This document is copyright. Apart from any fair dealing for the purposes of private study, research, review or
criticism, as permitted under the Copyright Act, no part may be reproduced by any process without written
permission from CHEMWATCH. TEL (+61 3) 9572 4700.
Issue Date: 6-Jul-2008
Print Date: 24-Aug-2010
This is the end of the MSDS.